Omer Sub Complete Brown Handle For Cayman Gi Mimetic
Lid for the ballast compartment, indispensable for balancing your weapon, has a convenient wire pass, which can be cut if necessary, leads not supplied, measures of interest 18 mm x 90 mm, complete with inserts and screws M4 x 25 mm.
Single block with two Derlin pulleys, allows you to attach up to 7 elastic bands for geared inverter systems, openable, light, the pulleys are in derlin without bearings, we opt for this solution as the micro bearings currently on the market do not allow exaggerated loads.
AIR PACIFIC Tahitian. Double fin ø7.5mm stainless steel 17-4PH.
Finally the perfect replacement for Pathos Dangelo 1 Handle, Mechanism entirely in steel with Ermes Double Roller mechanics and side line release, it will be necessary to cut a couple of mm where the line release is and widen the where there is the safety from 4 to 6 mm, very easy to do as it is plastic. Separately, it is possible to buy Sternal Support Assembly instructions 1. Remove original mechanism by punching the rear pin out 2. Remove safety by using flat head screw driver to flick th
Hermes specific support for the New Back mechanism, adaptable also to all other models of the mechanisms Hermes, in conjunction with the Cross Arm, it is mounted using the fastening holes of the same mechanisms, without making additional holes in the guns. Supplied to the support you have the 1/4 american and a rubber washer, the camera can be mounted into the hole using only the support.
Kit of two Salvimar wishbones with stainless steel bow and 16mm nylon bushings for mounting a pair of elastic bands on spearguns. For this reason, the kit includes two spinners with narrow headband for the first internal elastic and one spinner with large headband for the second elastic. In this solution Salvimar guarantees the perfect alignment of the two elastics while remaining parallel to each other.
Sporasub Reel Attachment Kit For Beuchat Spearguns
Heat treated, hardened, finned stainless steel, flopper style spear shaft. It uses three flaps to facilitate loading instead of notches.
The dimensions of the mobile arm vary according to the 80/40 model: the first, measuring 115x50, the second 90x50, both 2mm thick, in AISI 304 stainless steel and anticorodal aluminum with hard anodizing treatment which prevents the alloy from oxidizing in salt water . The light alloy bracket weighs 1/3 of the stainless steel one. The end where the camera is applied is equipped with holes and slots that allow in any case an easy application of the camera. The central hole is used when fixing
Stainless steel shaft with fins for Cressi Cherokee Ocean / Pacific speargun Ø 7 mm.
Tahitian salvimar shaft with single flap for mares cyrano pneumatic rifles and 7mm salvimar vintair / predathor.
The "Ocean" auction concept It is a sturdy rod, very refined, built with precious materials, rigid, it mounts sturdy and hydrodynamic fins, precise and very versatile for traditional arbaletes, rollerballs and with American style closed rod. Conetto not included in the auction, only on specific request it is assembled. Ocean rod technical description The Oceano auction is built in 17.4 PH adjusted It is produced with 17.4 PH bars certified by the steel mill; straight and smooth The
Kit consisting of a 1.4mm high tenacity nylon monofilament line ideal for mounting and reinforcing the speargun speargun rods. Number 20 pieces of 1.4mm wire-stop sleeves.
Cressi Sub Fiocina with 5 narrow stainless steel tips with nylon base and very resistant standard thread for use on threaded rods of arbalète and oleopneumatic for spearfishing. In the nylon base there is a housing for the fingers for reloading the pneumatic spearguns.
The Invictus Carbon rifle is characterized by aggressive lines that recall its spirit (made in Italy), the release device is very sensitive thanks to the use of stainless steel and elongated internal levers. This allows you to obtain sweetness when shooting even with powerful equipment. The cylindrical stem is made entirely of carbon worked and made in Italy, the rod guide is then applied to the stem. This guarantees a very high production quality and absolute rigidity. The carbon finish is op
Turned from solid in floating plastic, the stopper is in shockproof material, created expressly for cable systems, supplied with 2 o rings that can be moved at will in the 3 special seats, in two models, with high speed steel bearings (mod Iron) and with pulleys with highly smooth Sliding core (Mod. Sliding). Screw and washers M4 x 60 included.
New generation "tri-extruded" tires: very fast but progressive !!! In Sporasub the new green 3-layer rubbers (GREEN SHOT), have an elongation factor of 3.2 and are very reactive, especially recommended in mono rubber, but are also good in double when looking for a burning shot. Of the 3 layers that make up the rubber, the green exterior serves to protect the internal latex from light sources and corrosive agents. It also provides him with a camouflage coloring. The central layer in pure la
New generation shotgun with innovative ultra-resistant stainless steel mechanism, reinforced aluminum barrel with a diameter of 28mm and built-in rod guide. 6.5mm shaft with fins, 17mm single circular elastic with dyneema ogive in sizes up to 90cm while sizes 100 and 115 are equipped with double 14mm elastic. Reel included as standard. ■ Ø 28MM CIRCULAR SECTION DRUM. MADE OF ANTICORODAL EXTRUDED ALUMINUM WITH INTEGRATED LOW FRICTION UPPER ROD GUIDE ■ OPEN HEAD WITH FRICTION REDUCTION
The original Cressi temples, in the 6 mm and 6.5 mm versions, offer exceptional durability thanks to the special 174PH stainless steel construction. They are highly resistant to shock and bending. The 6 mm shaft is fitted as standard on original Cressi spearguns in the following sizes: COMANCHE RAIL 60 / MOICANO 60 / YUMA 60 Rod Length 90 CM CHEROKEE 60 / MOICANO 75 / YUMA 75 Rod Length 105 CM COM. RAIL 75 / CHER. 75 / MOI. 85 / YUMA 85 Rod Length 115 CM MOICANO 95 / YUMA 95 Rod Length 1
This mechanism now has the possibility of mounting in the internal components, the Double Roll system, with reduction operation, thanks to its innovative internal components (Patented), this system allows to have a sensitivity on the trigger unthinkable with traditional mechanisms at very high loads, (maximum triggering effort 0.500 kg on 300 kg traction !!!) with a practically unlimited duration of the rod coupling component. In addition to the new look, this mechanism has minor changes in b
Made with harmonic steel, they have a shape similar to the original Mustad. Conceived for spearfishing, the new line of harpoons is made up of 6 different models with a new design of the tips and base in polymers. The polymer base is made of elastomeric PA66, has a revolutionary hydrodynamic shape with reinforcements around the tips, where there is the greatest stress. A harmonic steel rod is inserted inside the polymer base. The auction, unlike the other harpoons on the market, is posit
The high-strength nylon monofilament lines are the most suitable for arming the spearguns. The specific Omer Cable Clamp Pliers are recommended for closing sleeves safely and hydrodynamically.
Rods equipped with 3 laser welded fins to ensure maximum resistance. The profile of these fins is very thin in order to obtain maximum hydrodynamics and penetration into the prey. All fins are equipped with a hole to be able to fix the monofilament directly. These rods are burnished and are equipped with an ogive tip that increases the penetration into the meat of the preys.
- High modulus carbon fiber shaft with integral rod guide - Profile designed for a better set-up and swing - Shock Absorber foam filling - Handle with Metal release system - Sensitive trigger adjustment - Easily removable sternal support - Reinforced Enclosed Track head in lengths 115cm and 125cm - Multi-elastic open head - Double Elastics tied as standard 14mm with Dyneema ogive - Rod with 6.5mm laser-welded fins in shotgun size from 85 to 105 and 7.0mm in shotgun size 115cm a
New patented grease that allows to eliminate the traditional oil from the tank of pneumatic spearfishing spearguns. This grease clings at the molecular level to the aluminum of the barrel ensuring perfect lubrication and smoothness of the piston for hundreds of shots with relative increase in the performance of the rifle. Thanks to the use of this grease and the consequent elimination of the oil, it is possible to load and unload the compressed air tank quickly and without the escape of the
And obtain 5 € of discount on your first order.